Welcome, Guest. Please login or register.


Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - leonlas

Pages: [1]
1
Hardware / Re: Problem RGB - SCART.
« on: 2020.December.09. 00:45:18 »
I wanted to make an adapter to use a standard SCART cable. It's a prototype in the photo. I need a housing and everything on one PCB. I was supposed to mill the plate but I have to think about it ...

2
Hardware / Re: Problem RGB - SCART.
« on: 2020.December.09. 00:09:51 »
Don’t get mad, but I wouldn’t trust an adapter in this state.
Gflorez is right. Try it with a suitable cable.

(Attachment Link)

(Attachment Link)

Great plug 4 EP64! Do you make them yourself? Maybe you have to sell? I mean the plug itself without a cable and Scart.

3
Hardware / Re: Problem RGB - SCART.
« on: 2020.December.09. 00:03:49 »
And that's it: an adapter! I made it without 19pin-20pin crossover and that's the effect. The first time I decided to do it on an adapter and my routine failed me. I forgot about the crossover. Before reading the rest of the posts, I decided to do without an adapter. IT LIVES! hahahahaha! The image is a bit bright but I will add a resistor and it will be ok.
I can see there is a really helpful community here - many thanks to YOU.

:smt041

4
Hardware / Re: Problem RGB - SCART.
« on: 2020.December.08. 19:16:58 »
He does not get nervous :-)
I did two and both would be bad .... maybe.
I have to solder directly to SCART and then it will be sure.
I've already made several dozen RGB cables for various 8/16 bit and they all work ;-)
But it must be the first time sometime.
I will check without this grommet, let me know.

5
Hardware / Re: Problem RGB - SCART.
« on: 2020.December.08. 18:33:19 »
I tried 2 different SCART - SCART cables.
Today I will connect to the third TV and maybe the LCD TV.
I connect through this adapter of my job:
I have 2 of these, one with resistors, the other without.

6
Hardware / Re: Problem RGB - SCART.
« on: 2020.December.08. 16:36:18 »
You put it right: stable image. Yes.

And if SCART is connected, despite the bad picture, should there be sound? For example, beeping from the keyboard? Audible on tv -SCART.

7
Hardware / Re: Problem RGB - SCART.
« on: 2020.December.08. 14:59:31 »
I tried to connect A3 - no good change.
I tried to turn the coil - unfortunately it doesn't help either.
I checked the resistor - it's okey 100ohm.
I have 2 E64 units and both have the same problem.
The output from the modulator gives the "correct" signal ;-)   .

I connected the signal coming before the modulator, composite and the image is in colors and it does not jump but I want RGB and ...... ;-(

This is the effect of RGB as in the pictures below.

8
Hardware / Problem RGB - SCART.
« on: 2020.December.07. 22:32:29 »
Hi.
 I'm new to the forum. I bought an E64 from egypt and started it. I changed the capacitors and measured the power, it is 5V and 12V.
I made a plug for RGB - scart for TV. Here's the problem: it can't catch sync. The image is in color but it floats diagonally to the side and up and down. The resistors are RGB and CSYNC. First I gave 100 ohms, then changed to 330 ohms. 12V is connected to pin 8 on SCART and from 8 to 16 a 470 ohm resistor. There is still a problem. I measured RGB multimeter and it's 0.2V CSYNC has 3V. I tried to lower the Volts on CSYNC with a potentiometer (resistor) but it does not change either. The same effect is present on two TVs. I also have a second E64 and there is the same trouble.
I don't know what to look for. Can someone help me - give me a hint?

Pages: [1]