Welcome, Guest. Please login or register.


Author Topic: EP BUS hoszabbító max: 1-2m - EP bus lengthener max: 1-2m (Read 1271 times)

Offline Tuby128

  • EP addict
  • *
  • Posts: 1448
  • Country: hu
For english version of this post see below.

:HUN

Új hardver fejlesztésén töröm a fejemet.

Arra gondoltam, hogy az EP bővítő élcsatlakozójára rádugnék egy picike bedobozolt áramkört. Ez csak 2-3 cm széles lenne. Erre a dobozra rá lehet dugni 1 vagy 2 kábelt, ami max 1-2 méter hosszú lehetne. (ez a hossz csak egy becslés)
 A kábel másik oldalán egy visszaalakító lenne, ami egy 2x33 pines élcsatlakozóban végződne. Ezt aztán rá lehet dugni akár egy exdos kártyára akár egy spectrum emulátorra, esetleg speciális USB 2.0 átalakítón keresztül egy PC-re.
 A lényeg hogy az EP buszát meghosszabítanám úgy, hogy a túloldalon az eszközök akár mozgathatóak is lehetnek a flexi kábel miatt.
 Az összekapcsoláshoz a legnépszerűbb technikát választanám, egy lapos ethernet kábelt RJ-45-ös csatlakozóval, persze NEM IP protokoll futna rajta hanem LVDS jelek.
A kábelről kép a csatolmányban.
 Gyakorlatilag az EP lassú párhuzamos jeleit átalakítanám gyors soros jelekké, és azokat átküldeném a kábelen, majd visszalakítanám újra párhuzamos jelekké.
 Tehát a
24 cím bit
8 adat bit
+23 más jel (RD, WR, WAIT, INT, RESET ... stb)
összesen kb 55 jelből egy kb 8 BYTE-ot állítanék elő, amit aztán sorosan villámgyorsan átküldenék mindkét irányban a 2x4 éren. Természetesen az irányokat figyelembe fogom venni.

 A nagyon gyakran használt eszközöket szeretném első sorban rákötni, mint exdos, vagy akár egy buszkiterjesztő egységet, hogy a memória bővítő óra modul és egyéb ilyesmi bedobozolva az asztal alatt vagy a monitor mellett lehessen.
 Kérdés, hogy mely jelek hagyhatóak ki a listából. Pl a Z80 órajele, illetve a NICK chip jeleinek nem látom értelmét továbbküldeni. Nem zárkózom el tőle, csak jó lenne megindokolni hogy miért kellhet.
 
:UK

 I am thinking to make a new hardware.

 My idea would be a small boxed PCB which can be connected to the EP Bus expansion connector. This box would be 20-30mm width. And we could plug on that box 1 or 2 cables, which could be max 1-2m long. (the length is just an estimation)
On the other side of the cable would be a translator, which ends in a 2x33 pin edge connector. This connector than could be connected to a exdos card or maybe a spectrum emulator card. I can imagine an EP-BUS/USB 2.0 converter to connect the EP to an PC.
The main thing is I want to lengthen the EP bus, that on the other side the devices would be moveable because of the flexible cable.
 For the connection I would use the most popular technology, a slim ethernet cable witch RJ-45 connection, of course NOT with IP-Protocoll, I would use LVDS signals.
A picture from the cable is in the attachment.
 Practically I would transfer the slow parallel EP signals into fast differential serial signals, and send them over the cable, on the other side I would transfer back to parallel signals.
Thus the
- 24 Adress bits
- 8 Data bits
+ 23 other signals (RD, WR, WAIT, INT, RESET ... etc)
these are about 55 signals which can be converted to a 8 BYTE, which I would send lightning-fast both direction over the 2x4 wires. Of course, I am going to keep in mind the directions.

I would give support mainly the very often used devices, like EXDOS or the Bus-Expansion (distributor) device which has more socket for more devices, thus a connected memory expansion card, clock module, etc. could be placed under the desk or next to the monitor.
The question is which signals can we left out from the list. For example, the clock signal of the Z80, or some signals for the Nick, I cannot see why I should send them over. I am not excluding the possibility, I need only a strong reason why we might need it.
« Last Edit: 2022.January.10. 05:46:07 by Tuby128 »

Offline gflorez

  • EP addict
  • *
  • Posts: 3607
  • Country: es
    • Támogató Támogató
Re: EP BUS hoszabbító max: 1-2m - EP bus lengthener max: 1-2m
« Reply #1 on: 2022.January.11. 10:33:08 »
Nagyon érdekesnek látom ezt az ötletet, de..... voltak sikeres kísérletek akár 1m-es lapos kábellel(Werner Lindner) az összes jellel, külső HD-t futtatva.

------

I see this idea very interesting but..... there were successful experiments made with up to 1m flat cable(Werner Lindner) with all the signals, running an external HD.
« Last Edit: 2022.January.11. 10:39:23 by gflorez »

Offline Tuby128

  • EP addict
  • *
  • Posts: 1448
  • Country: hu
Re: EP BUS hoszabbító max: 1-2m - EP bus lengthener max: 1-2m
« Reply #2 on: 2022.January.11. 12:36:20 »
I was thinking, I will going to add some error identification bits to the serial stream, that way my system will always work stable.